View HYE18L256169BFX-75_4122376.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

January 2007
HYB18L256169BFX-7.5 HYE18L256169BFX-7.5
DRAMs for Mobile Applications 256-Mbit Mobile-RAM RoHS Compliant Product
Data Sheet
R ev . 1 . 01
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
HYE18L256169BFX-7.5 Revision History: 2007-01 , Rev. 1.01 Page All Subjects (major changes since last revision) New Qimonda Template
We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc@Qimonda.com Data Sheet 2 Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Overview
1
1.1
* * * * * * * * * * * * *
Overview
Features
4 banks x 4 Mbit x 16 organization Fully synchronous to positive clock edge Four internal banks for concurrent operation Programmable CAS latency: 2, 3 Programmable burst length: 1, 2, 4, 8 or full page Programmable wrap sequence: sequential or interleaved Programmable drive strength Auto refresh and self refresh modes 8192 refresh cycles / 64 ms Auto precharge Commercial (0C to +70C) and Extended (-25C to +85C) operating temperature range 54-ball PG-VFBGA package (11.0 x 8.0 x 1.0 mm) RoHS Compliant Product1)
Power Saving Features * * * * * Low supply voltages: VDD = 1.70V to 1.95V, VDDQ = 1.70V to 1.95V Optimized self refresh (IDD6) and standby currents (IDD2/IDD3) Programmable Partial Array Self Refresh (PASR) Temperature Compensated Self-Refresh (TCSR), controlled by on-chip temperature sensor Power-Down and Deep Power Down modes Performance - 7.5 133 CL = 3 CL = 2 Clock Cycle Time (tCKmin) CL = 3 CL = 2 Table 2 Item Banks Rows Columns Memory Addressing Scheme Addresses BA0, BA1 A0 - A12 A0 - A8 5.4 6.0 7.5 9.5 Unit MHz ns ns ns ns
Table 1
Part Number Speed Code Speed Grade Access Time (tACmax)
1)RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers.
Data Sheet
3
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Overview Table 3 Type
1)
Ordering Information Package 133 MHz 4 Banks x 4 Mbit x 16 LP-SDRAM 133 MHz 4 Banks x 4 Mbit x 16 LP-SDRAM Description PG-VFBGA-54-8 PG-VFBGA-54-8
Commercial Temperature Range HYB18L256169BFX-7.5 HYE18L256169BFX-7.5 Extended Temperature Range
1) HY[B/E]: Designator for memory products (HYB: commercial temp. range); (HYE: extended temp. range) 18L: 1.8V Mobile-RAM 256: 256 MBit density 160: 16 bit interface width B: die revision F: green product X: relaxed standby current -7.5: speed grade(s): min. clock cycle time
1.2
Pin Configuration
Figure 1
Standard Ballout 256-Mbit Mobile-RAM
1.3
Description
The HY[B/E]18L256169BFX is a high-speed CMOS, dynamic random-access memory containing 268,435,456 bits. It is internally configured as a quad-bank DRAM. The HY[B/E]18L256169BFX achieves high speed data transfer rates by employing a chip architecture that prefetches multiple bits and then synchronizes the output data to the system clock. Read and write accesses are burst-oriented; accesses start at a selected location and continue for a programmed number of locations (1, 2, 4, 8 or full page) in a programmed sequence. The device operation is fully synchronous: all inputs are registered at the positive edge of CLK. The HY[B/E]18L256169BFX is especially designed for mobile applications. It operates from a 1.8V power supply. Power consumption in self refresh mode is drastically reduced by an On-Chip Temperature Sensor (OCTS); it can further be reduced by using the programmable Partial Array Self Refresh (PASR). A conventional data-retaining Power-Down (PD) mode is available as well as a non-data-retaining Deep PowerDown (DPD) mode.
Data Sheet
4
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Overview The HY[B/E]18L256169BFX is housed in a 54-ball PG-VFBGA package. It is available in Commercial (0 C to 70 C) and Extended (-25 C to 85 C) temperature range.
Figure 2
Functional Block Diagram
1.4
Table 4 Ball CLK CKE
Pin Definition and Description
Pin Description Type Input Input Detailed Function Clock: all inputs are sampled on the positive edge of CLK. Clock Enable: CKE HIGH activates and CKE LOW deactivates internal clock signals, device input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER-DOWN and SELF REFRESH operation (all banks idle), ACTIVE POWERDOWN (row active in any bank) or SUSPEND (access in progress). Input buffers, excluding CLK and CKE are disabled during power-down. Input buffers, excluding CKE are disabled during SELF REFRESH.
Data Sheet
5
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Overview Table 4 Ball CS Pin Description (cont'd) Type Input Detailed Function Chip Select: All commands are masked when CS is registered HIGH. CS provides for external bank selection on systems with multiple memory banks. CS is considered part of the command code. Command Inputs: RAS, CAS and WE (along with CS) define the command being entered. Data Inputs/Output: Bi-directional data bus (16 bit) Input/Output Mask: input mask signal for WRITE cycles and output enable for READ cycles. For WRITEs, DQM acts as a data mask when HIGH. For READs, DQM acts as an output enable and places the output buffers in High-Z state when HIGH (two clocks latency). LDQM corresponds to the data on DQ0 - DQ7; UDQM to the data on DQ8 - DQ15. Bank Address Inputs: BA0 and BA1 define to which bank an ACTIVATE, READ, WRITE or PRECHARGE command is being applied. BA0, BA1 also determine which mode register is to be loaded during a MODE REGISTER SET command (MRS or EMRS). Address Inputs: A0 - A12 define the row address during an ACTIVE command cycle. A0 - A8 define the column address during a READ or WRITE command cycle. In addition, A10 (= AP) controls Auto Precharge operation at the end of the burst read or write cycle. During a PRECHARGE command, A10 (= AP) in conjunction with BA0, BA1 controls which bank(s) are to be precharged: if A10 is HIGH, all four banks will be precharged regardless of the state of BA0 and BA1; if A10 is LOW, BA0, BA1 define the bank to be precharged. During MODE REGISTER SET commands, the address inputs hold the opcode to be loaded.
RAS, CAS, WE DQ0 - DQ15 LDQM, UDQM
Input I/O Input
BA0, BA1
Input
A0 - A12
Input
VDDQ VSSQ VDD VSS
N.C.
Supply I/O Power Supply: Isolated power for DQ output buffers for improved noise immunity: VDDQ = 1.70V to 1.95V Supply I/O Ground Supply Power Supply: Power for the core logic and input buffers, VDD = 1.70V to 1.95V Supply Ground - No Connect
Data Sheet
6
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2
Functional Description
The 256-Mbit Mobile-RAM is a high-speed CMOS, dynamic random-access memory containing 268,435,456 bits. It is internally configured as a quad-bank DRAM. READ and WRITE accesses to the Mobile-RAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed (BA0, BA1 select the banks, A0 - A12 select the row). The address bits registered coincident with the READ or WRITE command are used to select the starting column location for the burst access. Prior to normal operation, the Mobile-RAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command description and device operation.
2.1
Power On and Initialization
The Mobile-RAM must be powered up and initialized in a predefined manner (see Figure 3). Operational procedures other than those specified may result in undefined operation.
Figure 3
Power-Up Sequence and Mode Register Sets
Data Sheet
7
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description 1. At first, device core power (VDD) and device IO power (VDDQ) must be brought up simultaneously. Typically VDD and VDDQ are driven from a single power converter output. Assert and hold CKE and DQM to a HIGH level. 2. After VDD and VDDQ are stable and CKE is HIGH, apply stable clocks. 3. Wait for 200s while issuing NOP or DESELECT commands. 4. Issue a PRECHARGE ALL command, followed by NOP or DESELECT commands for at least tRP period. 5. Issue two AUTO REFRESH commands, each followed by NOP or DESELECT commands for at least tRC period. 6. Issue two MODE REGISTER SET commands for programming the Mode Register and Extended Mode Register, each followed by NOP or DESELECT commands for at least tMRD period; the order in which both registers are programmed is not important. Programming of the Extended Mode Register may be omitted when default values (half drive strength, 4 bank refresh) will be used. Following these steps, the Mobile-RAM is ready for normal operation.
2.2 2.2.1
Register Definition Mode Register
The Mode Register is used to define the specific mode of operation of the Mobile-RAM. This definition includes the selection of a burst length (bits A0-A2), a burst type (bit A3), a CAS latency (bits A4-A6), and a write burst mode (bit A9). The Mode Register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. The Mode Register must be loaded when all banks are idle, and the controller must wait the specified time before initiating any subsequent operation. Violating either of these requirements results in unspecified operation. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. MR Mode Register Definition
BA1 0 BA0 0 A12 0 A11 0 A10 0 A9 WB
(BA[1:0] = 00B)
A8 0 A7 0 A6 A5 CL A4 A3 BT A2 A1 BL A0
Field WB
Bits 9
Type w
Description Write Burst Mode 0 Burst Write 1 Single Write CAS Latency 010 2 011 3 Note: All other bit combinations are RESERVED. Burst Type 0 Sequential 1 Interleaved
CL
[6:4]
w
BT
3
w
Data Sheet
8
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description Field BL Bits [2:0] Type w Description Burst Length 000 1 001 2 010 4 011 8 111 full page (Sequential burst type only) Note: All other bit combinations are RESERVED.
2.2.1.1
Burst Length
READ and WRITE accesses to the Mobile-RAM are burst oriented, with the burst length being programmable. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command. Burst lengths of 1, 2, 4, 8 locations are available for both the sequential and interleaved burst types, and a full-page burst mode is available for the sequential burst type. When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the burst wraps within the block if a boundary is reached. The block is uniquely selected by A1-A8 when the burst length is set to two, by A2-A8 when the burst length is set to four and by A3-A8 when the burst length is set to eight. The remaining (least significant) address bit(s) is (are) used to select the starting location within the block. Full page bursts wrap within the page if the boundary is reached. Please note that full page bursts do not selfterminate; this implies that full-page read or write bursts with Auto Precharge are not legal commands. Table 5 Burst Definition Starting Column Address A2 2 4 0 0 1 1 8 0 0 0 0 1 1 1 1 Full Page Notes 1. 2. 3. 4. For a burst length of 2, A1-Ai select the two-data-element block; A0 selects the first access within the block. For a burst length of 4, A2-Ai select the four-data-element block; A0-A1 select the first access within the block. For a burst length of 8, A3-Ai select the eight-data-element block; A0-A2 select the first access within the block. For a full page burst, A0-Ai select the starting data element. 9 Rev. 1.01, 2007-01 07062006-V6ZK-PGR3 n 0 0 1 1 0 0 1 1 n A1 A0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 n Sequential 0-1 1-0 0-1-2-3 1-2-3-0 2-3-0-1 3-0-1-2 0-1-2-3-4-5-6-7 1-2-3-4-5-6-7-0 2-3-4-5-6-7-0-1 3-4-5-6-7-0-1-2 4-5-6-7-0-1-2-3 5-6-7-0-1-2-3-4 6-7-0-1-2-3-4-5 7-0-1-2-3-4-5-6 Cn, Cn+1, Cn+2, ... Order of Accesses Within a Burst Interleaved 0-1 1-0 0-1-2-3 1-0-3-2 2-3-0-1 3-2-1-0 0-1-2-3-4-5-6-7 1-0-3-2-5-4-7-6 2-3-0-1-6-7-4-5 3-2-1-0-7-6-5-4 4-5-6-7-0-1-2-3 5-4-7-6-1-0-3-2 6-7-4-5-2-3-0-1 7-6-5-4-3-2-1-0 not supported
Burst Length
Data Sheet
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description 5. Whenever a boundary of the block is reached within a given sequence, the following access wraps within the block.
2.2.1.2
Burst Type
Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the burst type and is selected via bit A3. The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column address, as shown in Table 5.
2.2.1.3
Read Latency
The Read latency, or CAS latency, is the delay, in clock cycles, between the registration of a READ command and the availability of the first piece of output data. The latency can be programmed to 2 or 3 clocks. If a READ command is registered at clock edge n, and the latency is m clocks, the data will be available with clock edge n + m (for details please refer to the READ command description).
2.2.1.4
Write Burst Mode
When A9 = 0, the burst length programmed via A0-A2 applies to both read and write bursts; when A9 = 1, write accesses consist of single data elements only.
2.2.1.5
Extended Mode Register
The Extended Mode Register controls additional low power features of the device. These include the Partial Array Self Refresh (PASR, bits A0-A2)), the Temperature Compensated Self Refresh (TCSR, bits A3-A4)) and the drive strength selection for the DQs (bits A5-A6). The Extended Mode Register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 1) and will retain the stored information until it is programmed again or the device loses power. The Extended Mode Register must be loaded when all banks are idle, and the controller must wait the specified time before initiating any subsequent operation. Violating either of these requirements result in unspecified operation. Reserved states should not be used, as unknown operation or incompatibility with future versions may result. EMR Extended Mode Register
BA1 1 BA0 0 A12 0 A11 0 A10 0 A9 0
(BA[1:0] = 10B)
A8 0 A7 0 A6 DS A5 A4 A3 A2 A1 PASR A0
(TCSR)
Field DS
Bits [6:5]
Type w
Description Selectable Drive Strength 00 Full Drive Strength 01 Half Drive Strength (default) Note: All other bit combinations are RESERVED. Temperature Compensated Self Refresh XX Superseded by on-chip temperature sensor (see text)
TCSR [4:3]
w
Data Sheet
10
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description Field Bits Type w Description Partial Array Self Refresh 000 all banks (default) 001 1/2 array (BA1 = 0) 010 1/4 array (BA1 = BA0 = 0) 101 1/8 array (BA1 = BA0 = RA12 = 0) 110 1/16 array (BA1 = BA0 = RA12 = RA11 = 0) Note: All other bit combinations are RESERVED.
PASR [2:0]
2.2.1.6
Partial Array Self Refresh (PASR)
Partial Array Self Refresh is a power-saving feature specific to Mobile RAMs. With PASR, self refresh may be restricted to variable portions of the total array. The selection comprises all four banks, two banks, one bank, half of one bank, and a quarter of one bank. Data written to the non activated memory sections will get lost after a period defined by tREF (cf. Table 13).
2.2.1.7
Temperature Compensated Self Refresh (TCSR) with On-Chip Temperature Sensor
DRAM devices store data as electrical charge in tiny capacitors that require a periodic refresh in order to retain the stored information. This refresh requirement heavily depends on the die temperature: high temperatures correspond to short refresh periods, and low temperatures correspond to long refresh periods. The Mobile-RAM is equipped with an on-chip temperature sensor which continuously senses the actual die temperature and adjusts the refresh period in Self Refresh mode accordingly. This makes any programming of the TCSR bits in the Extended Mode Register obsolete. It also is the superior solution in terms of compatibility and power-saving, because * * * it is fully compatible to all processors that do not support the Extended Mode Register it is fully compatible to all applications that only write a default (worst case) TCSR value, e.g. because of the lack of an external temperature sensor it does not require any processor interaction for regular TCSR updates
2.2.1.8
Selectable Drive Strength
The drive strength of the DQ output buffers is selectable via bits A5 and A6 and shall be set load dependent. The half drive strength is suitable for typical Mobile-RAM applications.
Data Sheet
11
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.3
State Diagram
Figure 4 Data Sheet
State Diagram 12 Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4
Table 6 Command NOP ACT RD WR BST PRE ARF MRS - -
Commands
Command Overview CS RAS CAS WE DQM H L L L L L L L L - - X H L H H H L L L - - X H H L L H H L L - - X H H H L L L H L - - X X X L/H L/H X X X X L H Address X X Bank / Row Bank / Col Bank / Col X Code X Op-Code - - Notes
1) 1) 2) 3) 3) 4)
DESELECT NO OPERATION ACTIVE (Select bank and row) READ (Select bank and column and start read burst) WRITE (Select bank and column and start write burst) BURST TERMINATE or DEEP POWER DOWN PRECHARGE (Deactivate row in bank or banks) AUTO REFRESH or SELF REFRESH (enter self refresh mode) MODE REGISTER SET Data Write / Output Enable Write Mask / Output Disable (High-Z)
5) 6)7)
8) 9) 9)
1) DESELECT and NOP are functionally interchangeable. 2) BA0, BA1 provide bank address, and A0 - A12 provide row address. 3) BA0, BA1 provide bank address, A0 - A8 provide column address; A10 HIGH enables the Auto Precharge feature (non persistent), A10 LOW disables the Auto Precharge feature. 4) This command is BURST TERMINATE if CKE is HIGH, DEEP POWER DOWN if CKE is LOW. The BURST TERMINATE command is defined for READ or WRITE bursts with Auto Precharge disabled only. 5) A10 LOW: BA0, BA1 determine which bank is precharged. A10 HIGH: all banks are precharged and BA0, BA1 are "Don't Care". 6) This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW. 7) Internal refresh counter controls row and bank addressing; all inputs and I/Os are "Don't Care" except for CKE. 8) BA0, BA1 select either the Mode Register (BA0 = 0, BA1 = 0) or the Extended Mode Register (BA0 = 0, BA1 = 1); other combinations of BA0, BA1 are reserved; A0 - A12 provide the op-code to be written to the selected mode register. 9) DQM LOW: data present on DQs is written to memory during write cycles; DQ output buffers are enabled during read cycles; DQM HIGH: data present on DQs are masked and thus not written to memory during write cycles; DQ output buffers are placed in High-Z state (two clocks latency) during read cycles.
Address (A0 - A12, BA0, BA1), write data (DQ0 - DQ15) and command inputs (CKE, CS, RAS, CAS, WE, DQM) are all registered on the positive edge of CLK. Figure 5 shows the basic timing parameters, which apply to all commands and operations.
Figure 5 Data Sheet
Address / Command Inputs Timing Parameters 13 Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Table 7 Parameter
Inputs Timing Parameters Symbol min. CL = 3 CL = 2 CL = 3 CL = 2 - 7.5 max. -- -- 133 105 -- -- -- -- ns ns MHz MHz ns ns ns ns -- -- -- -- -- -- 7.5 9.5 -- -- 2.5 2.5 1.5 0.5 Unit Notes
Clock cycle time Clock frequency Clock high-level width Clock low-level width Address and command input setup time Address and command input hold time
tCK fCK tCH tCL tIS tIH
2.4.1
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform a NOP to a Mobile-RAM which is selected (CS = LOW). This prevents unwanted commands from being registered during idle states. Operations already in progress are not affected.
Figure 6
No Operation Command
2.4.2
DESELECT
The DESELECT function (CS = HIGH) prevents new commands from being executed by the Mobile-RAM. The Mobile-RAM is effectively deselected. Operations already in progress are not affected.
Data Sheet
14
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.3
MODE REGISTER SET
The Mode Register and Extended Mode Register are loaded via inputs A0 - A12 (see mode register descriptions in Chapter 2.2). The MODE REGISTER SET command can only be issued when all banks are idle and no bursts are in progress. A subsequent executable command cannot be issued until tMRD is met.
Figure 7
Mode Register Set Command
Figure 8 Table 8 Parameter
Mode Register Definition Timing Parameters for Mode Register Set Command Symbol min. - 7.5 max. - 2 Units Notes -
MODE REGISTER SET command period
tMRD
tCK
Data Sheet
15
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.4
ACTIVE
Before any READ or WRITE commands can be issued to a bank within the Mobile-RAM, a row in that bank must be "opened" (activated). This is accomplished via the ACTIVE command and addresses A0 - A12, BA0 and BA1 (see Figure 9), which decode and select both the bank and the row to be activated. After opening a row (issuing an ACTIVE command), a READ or WRITE command may be issued to that row, subject to the tRCD specification. A subsequent ACTIVE command to a different row in the same bank can only be issued after the previous active row has been "closed" (precharged). The minimum time interval between successive ACTIVE commands to the same bank is defined by tRC. A subsequent ACTIVE command to another bank can be issued while the first bank is being accessed, which results in a reduction of total row-access overhead. The minimum time interval between successive ACTIVE commands to different banks is defined by tRRD.
Figure 9
ACTIVE Command
Figure 10 Table 9 Parameter
Bank Activate Timings Timing Parameters for ACTIVE Command Symbol min. - 7.5 max. - - - ns ns ns
1) 1) 1)
Units
Notes
ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE bank A to ACTIVE bank B delay
tRC tRCD tRRD
67 19 15
1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer.
Data Sheet
16
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.5
READ
Subsequent to programming the mode register with CAS latency and burst length, READ bursts are initiated with a READ command, as shown in Figure 11. Basic timings for the DQs are shown in Figure 12; they apply to all read operations and therefore are omitted from all subsequent timing diagrams. The starting column and bank addresses are provided with the READ command and Auto Precharge is either enabled or disabled for that burst access. If Auto Precharge is enabled, the row being accessed starts precharge at the completion of the burst, provided tRAS has been satisfied. For the generic READ commands used in the following illustrations, Auto Precharge is disabled.
Figure 11
READ Command
Figure 12
Basic READ Timing Parameters for DQs
Data Sheet
17
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description Table 10 Parameter Access time from CLK DQ low-impedance time from CLK DQ high-impedance time from CLK Data out hold time DQM to DQ High-Z delay (READ Commands) ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE to PRECHARGE command period PRECHARGE command period CL = 3 CL = 2 Timing Parameters for READ Symbol min. - 7.5 max. 5.4 6.0 - 7.0 - 2 - - 100k - ns ns ns ns ns - -
1) 1) 1) 1)
Units
Notes - -
tAC tAC tLZ tHZ tOH tDQZ tRC tRCD tRAS tRP
- - 1.0 3.0 2.5 - 67 19 45 19
tCK
ns ns ns ns
1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer.
During READ bursts, the valid data-out element from the starting column address is available following the CAS latency after the READ command. Each subsequent data-out element is valid nominally at the next positive clock edge. Upon completion of a READ burst, assuming no other READ command has been initiated, the DQs go to High-Z state. Figure 13 and Figure 14 show single READ bursts for each supported CAS latency setting.
Figure 13
Single READ Burst (CAS Latency = 2)
Data Sheet
18
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 14
Single READ Burst (CAS Latency = 3)
Data from any READ burst may be concatenated with data from a subsequent READ command. In either case, a continuous flow of data can be maintained. A READ command can be initiated on any clock cycle following a previous READ command, and may be performed to the same or a different (active) bank. The first data element from the new burst follows either the last element of a completed burst (Figure 15) or the last desired data element of a longer burst which is being truncated (Figure 16). The new READ command should be issued x cycles after the first READ command, where x equals the number of desired data elements.
Figure 15
Consecutive READ Bursts
Data Sheet
19
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 16
Random READ Bursts
Non-consecutive READ bursts are shown in Figure 17.
Figure 17
Non-Consecutive READ Bursts
2.4.5.1
READ Burst Termination
Data from any READ burst may be truncated using the BURST TERMINATE command (see Page 30), provided that Auto Precharge was not activated. The BURST TERMINATE latency is equal to the CAS latency, i.e. the BURST TERMINATE command must be issued x clock cycles before the clock edge at which the last desired data element is valid, where x equals the CAS latency for READ bursts minus 1. This is shown in Figure 18. The BURST TERMINATE command may be used to terminate a full-page READ which does not self-terminate.
Data Sheet
20
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 18
Terminating a READ Burst
2.4.5.2
Clock Suspend Mode for READ Cycles
Clock suspend mode allows to extend any read burst in progress by a variable number of clock cycles. As long as CKE is registered LOW, the following internal clock pulse(s) will be ignored and data on DQ will remain driven, as shown in Figure 19.
Figure 19
Clock Suspend Mode for READ Bursts
2.4.5.3
READ - DQM Operation
DQM may be used to suppress read data and place the output buffers into High-Z state. The generic timing parameters as listed in Table 10 also apply to this DQM operation. The read burst in progress is not affected and will continue as programmed.
Data Sheet
21
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 20
READ Burst - DQM Operation
2.4.5.4
READ to WRITE
A READ burst may be followed by or truncated with a WRITE command. The WRITE command can be performed to the same or a different (active) bank. Care must be taken to avoid bus contention on the DQs; therefore it is recommended that the DQs are held in High-Z state for a minimum of 1 clock cycle. This can be achieved by either delaying the WRITE command, or suppressing the data-out from the READ by pulling DQM HIGH two clock cycles prior to the WRITE command, as shown in Figure 21. With the registration of the WRITE command, DQM acts as a write mask: when asserted HIGH, input data will be masked and no write will be performed.
Figure 21
READ to WRITE Timing
2.4.5.5
READ to PRECHARGE
A READ burst may be followed by, or truncated with a PRECHARGE command to the same bank, provided that Auto Precharge was not activated. This is shown in Figure 22. Data Sheet 22 Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description The PRECHARGE command should be issued x clock cycles before the clock edge at which the last desired data element is valid, where x equals the CAS latency for READ bursts minus 1. Following the PRECHARGE command, a subsequent ACTIVE command to the same bank cannot be issued until tRP is met. Please note that part of the row precharge time is hidden during the access of the last data elements. In the case of a READ being executed to completion, a PRECHARGE command issued at the optimum time (as described above) provides the same operation that would result from the same READ burst with Auto Precharge enabled. The disadvantage of the PRECHARGE command is that it requires that the command and address busses be available at the appropriate time to issue the command. The advantage of the PRECHARGE command is that it can be used to truncate bursts.
Figure 22
READ to PRECHARGE Timing
Data Sheet
23
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.6
WRITE
WRITE bursts are initiated with a WRITE command, as shown in Figure 23. Basic timings for the DQs are shown in Figure 24; they apply to all write operations. The starting column and bank addresses are provided with the WRITE command, and Auto Precharge is either enabled or disabled for that access. If Auto Precharge is enabled, the row being accessed is precharged at the completion of the write burst. For the generic WRITE commands used in the following illustrations, Auto Precharge is disabled.
Figure 23
WRITE Command
Figure 24
Basic WRITE Timing Parameters for DQs
During WRITE bursts, the first valid data-in element is registered coincident with the WRITE command, and subsequent data elements are registered on each successive positive edge of CLK. Upon completion of a burst, assuming no other commands have been initiated, the DQs remain in High-Z state, and any additional input data is ignored. Figure 25 and Figure 26 show a single WRITE burst for each supported CAS latency setting.
Data Sheet
24
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description Table 11 Parameter DQ and DQM input setup time DQ input hold time DQM input hold time DQM write mask latency ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE to PRECHARGE command period WRITE recovery time PRECHARGE command period Timing Parameters for WRITE Symbol min. - 7.5 max. -- -- -- -- -- -- 100k -- -- ns ns ns -- -- -- --
1) 1) 1) 1) 1)
Units
Notes
tIS tIH tDQW tRC tRCD tRAS tWR tRP
1.5 0.8 0.5 0 67 19 45 14 19
tCK
ns ns ns ns ns
1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer.
Figure 25
WRITE Burst (CAS Latency = 2)
Data Sheet
25
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 26
WRITE Burst (CAS Latency = 3)
Data for any WRITE burst may be concatenated with or truncated with a subsequent WRITE command. In either case, a continuous flow of input data can be maintained. A WRITE command can be issued on any positive edge of clock following the previous WRITE command. The first data element from the new burst is applied after either the last element of a completed burst (Figure 27) or the last desired data element of a longer burst which is being truncated (Figure 28). The new WRITE command should be issued x cycles after the first WRITE command, where x equals the number of desired data elements.
Figure 27
Consecutive WRITE Bursts
Data Sheet
26
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 28
Random WRITE Bursts
Non-consecutive WRITE bursts are shown in Figure 29.
Figure 29
Non-Consecutive WRITE Bursts
2.4.6.1
WRITE Burst Termination
Data from any WRITE burst may be truncated using the BURST TERMINATE command (see Page 30), provided that Auto Precharge was not activated. The input data provided coincident with the BURST TERMINATE command will be ignored. This is shown in Figure 30. The BURST TERMINATE command may be used to terminate a full-page WRITE which does not self-terminate.
Data Sheet
27
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 30
Terminating a WRITE Burst
2.4.6.2
Clock Suspend Mode for WRITE Cycles
Clock suspend mode allows to extend any WRITE burst in progress by a variable number of clock cycles. As long as CKE is registered LOW, the following internal clock pulse(s) will be ignored and no data will be captured, as shown in Figure 31.
Figure 31
Clock Suspend Mode for WRITE Bursts
2.4.6.3
WRITE - DQM Operation
DQM may be used to mask write data: when asserted HIGH, input data will be masked and no write will be performed. The generic timing parameters as listed in Table 11 also apply to this DQM operation. The write burst in progress is not affected and will continue as programmed.
Data Sheet
28
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 32
WRITE Burst - DQM Operation
2.4.6.4
WRITE to READ
A WRITE burst may be followed by, or truncated with a READ command. The READ command can be performed to the same or a different (active) bank. With the registration of the READ command, data inputs will be ignored and no WRITE will be performed, as shown in Figure 33.
Figure 33
WRITE to READ Timing
2.4.6.5
WRITE to PRECHARGE
A WRITE burst may be followed by, or truncated with a PRECHARGE command to the same bank, provided that Auto Precharge was not activated. This is shown in Figure 34. The PRECHARGE command should be issued tWR after the clock edge at which the last desired data element of the WRITE burst was registered. Additionally, when truncating a WRITE burst, DQM must be pulled to mask input data presented during tWR prior to the PRECHARGE command. Following the PRE-CHARGE command, a subsequent ACTIVE command to the same bank cannot be issued until tRP is met. Data Sheet 29 Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description In the case of a WRITE being executed to completion, a PRECHARGE command issued at the optimum time (as described above) provides the same operation that would result from the same WRITE burst with Auto Precharge enabled. The disadvantage of the PRECHARGE command is that it requires that the command and address busses be available at the appropriate time to issue the command. The advantage of the PRECHARGE command is that it can be used to truncate bursts.
Figure 34
WRITE to PRECHARGE Timing
2.4.7
BURST TERMINATE
The BURST TERMINATE command is used to truncate READ or WRITE bursts (with Auto Precharge disabled). The most recently registered READ or WRITE command prior to the BURST TERMINATE command will be truncated, as shown in Figure 18 and Figure 30, respectively. The BURST TERMINATE command is not allowed for truncation of READ or WRITE bursts with Auto Precharge enabled.
Figure 35
BURST TERMINATE Command
Data Sheet
30
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.8
PRECHARGE
The PRECHARGE command is used to deactivate (close) the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access a specified time (tRP) after the PRECHARGE command is issued. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as "Don't Care". Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command will be treated as a NOP if there is no open row in that bank, or if the previously open row is already in the process of precharging.
Figure 36
PRECHARGE Command
2.4.8.1
AUTO PRECHARGE
Auto Precharge is a feature which performs the same individual-bank precharge functions described above, but without requiring an explicit command. This is accomplished by using A10 to enable Auto Precharge in conjunction with a specific READ or WRITE command. A precharge of the bank/row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. Auto Precharge is non persistent in that it is either enabled or disabled for each individual READ or WRITE command. Auto Precharge ensures that the precharge is initiated at the earliest valid stage within a burst. The user must not issue another command to the same bank until the precharge (tRP) is completed. This is determined as if an explicit PRECHARGE command was issued at the earliest possible time, as described for each burst type. Table 12 Parameter ACTIVE to PRECHARGE command period WRITE recovery time PRECHARGE command period Timing Parameters for PRECHARGE Symbol min. - 7.5 max. 100k - - ns ns ns
1) 1) 1)
Units
Notes
tRAS tWR tRP
45 14 19
1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer.
2.4.8.2
CONCURRENT AUTO PRECHARGE
A READ or WRITE burst with Auto Precharge enabled can be interrupted by a subsequent READ or WRITE command issued to a different bank.
Data Sheet
31
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description Figure 37 shows a READ with Auto Precharge to bank n, interrupted by a READ (with or without Auto Precharge) to bank m. The READ to bank m will interrupt the READ to bank n, CAS latency later. The precharge to bank n will begin when the READ to bank m is registered. Figure 38 shows a READ with Auto Precharge to bank n, interrupted by a WRITE (with or without Auto Precharge) to bank m. The precharge to bank n will begin when the WRITE to bank m is registered. DQM should be pulled HIGH two clock cycles prior to the WRITE to prevent bus contention. Figure 39 shows a WRITE with Auto Precharge to bank n, interrupted by a READ (with or without Auto Precharge) to bank m. The precharge to bank n will begin tWR after the new command to bank m is registered. The last valid data-in to bank n is one clock cycle prior to the READ to bank m. Figure 40 shows a WRITE with Auto Precharge to bank n, interrupted by a WRITE (with or without Auto Precharge) to bank m. The precharge to bank n will begin tWR after the WRITE to bank m is registered. The last valid data-in to bank n is one clock cycle prior to the WRITE to bank m.
Figure 37
READ with Auto Precharge Interrupted by READ
Figure 38
READ with Auto Precharge Interrupted by WRITE
Data Sheet
32
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
Figure 39
WRITE with Auto Precharge Interrupted by READ
Figure 40
WRITE with Auto Precharge Interrupted by WRITE
2.4.9
AUTO REFRESH and SELF REFRESH
The Mobile-RAM requires a refresh of all rows in a rolling interval. Each refresh is generated in one of two ways: by an explicit AUTO REFRESH command, or by an internally timed event in SELF REFRESH mode.
Data Sheet
33
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.9.1
AUTO REFRESH
Auto Refresh is used during normal operation of the Mobile-RAM. The command is non persistent, so it must be issued each time a refresh is required. A minimum row cycle time (tRC) is required between two AUTO REFRESH commands. The same rule applies to any access command after the auto refresh operation. All banks must be precharged prior to the AUTO REFRESH command. The refresh addressing is generated by the internal refresh controller. This makes the address bits "Don't Care" during an AUTO REFRESH command. The Mobile-RAM requires AUTO REFRESH cycles at an average periodic interval of 7.8 s (max.). Partial array mode has no influence on auto refresh mode.
Figure 41
AUTO REFRESH Command
Figure 42
Auto Refresh
Data Sheet
34
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.9.2
SELF REFRESH
The SELF REFRESH command can be used to retain data in the Mobile-RAM, even if the rest of the system is powered down. When in the self refresh mode, the Mobile-RAM retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command except CKE is LOW. Input signals except CKE are "Don't Care" during SELF REFRESH. The procedure for exiting SELF REFRESH requires a stable clock prior to CKE returning HIGH. Once CKE is HIGH, NOP commands must be issued for tRC because time is required for a completion of any internal refresh in progress. If during normal operation burst auto refresh or user controlled refresh is used, add 8192 auto refresh cycles just before self refresh entry and just after self refresh exit.
Figure 43
SELF REFRESH Entry Command
Figure 44 Table 13 Parameter
Self Refresh Entry and Exit Timing Parameters for AUTO REFRESH and SELF REFRESH Symbol min. - 7.5 max. - - 64 - ns ns ms
1) 1) 1) 1)
Units
Notes
ACTIVE to ACTIVE command period PRECHARGE command period Refresh period (8192 rows) Self refresh exit time
tRC tRP tREF tSREX
67 19 - 1
tCK
1) These parameters account for the number of clock cycles and depend on the operating frequency as follows: no. of clock cycles = specified delay / clock period; round up to next integer.
Data Sheet
35
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.4.10
POWER DOWN
Power-down is entered when CKE is registered LOW (no accesses can be in progress). If power-down occurs when all banks are idle, this mode is referred to as precharge power-down; if power-down occurs when there is a row active in any bank, this mode is referred to as active power-down. Entering power-down deactivates the input and output buffers, excluding CLK and CKE. CKE LOW must be maintained during powerdown. Power-down duration is limited by the refresh requirements of the device (tREF). The power-down state is synchronously exited when CKE is registered HIGH (along with a NOP or DESELECT command). One clock delay is required for power down entry and exit.
Figure 45
Power Down Entry Command
Figure 46
Power Down Entry and Exit
2.4.10.1
DEEP POWER DOWN
The deep power down mode is an unique function on Low Power SDRAM devices with extremely low current consumption. Deep power down mode is entered using the BURST TERMINATE command (cf. Figure 35) except that CKE is LOW. All internal voltage generators inside the device are stopped and all memory data is lost in this mode. To enter the deep power down mode all banks must be precharged. The deep power down mode is asynchronously exited by asserting CKE HIGH. After the exit, the same command sequence as for power-up initialization, including the 200s initial pause, has to be applied before any other command may be issued (cf. Figure 3 and Figure 4).
Data Sheet
36
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
2.5
Table 14 Any Idle
Function Truth Tables
Current State Bank n - Command to Bank n CS H L L L L L RAS CAS WE Command / Action X H L L L L H H L H H L H H H L H X H H L L H L L H L L H H L L H H X H H H L L H L L H L L L H L L L DESELECT (NOP / continue previous operation) NO OPERATION (NOP / continue previous operation) ACTIVE (select and activate row) AUTO REFRESH MODE REGISTER SET PRECHARGE READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) READ (select column and start new READ burst) WRITE (select column and start new WRITE burst) PRECHARGE (truncate READ burst, start precharge) BURST TERMINATE READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (truncate WRITE burst, start precharge) BURST TERMINATE Notes
1)2)3)4)5)6) 1) to 6) 1) to 6) 1) to 7) 1) to 7) 1) to 6), 8) 1) to 6), 9) 1) to 6), 9) 1) to 6), 10) 1) to 6), 9) 1) to 6), 9) 1) to 6), 10) 1) to 6), 11) 1) to 6), 9) 1) to 6), 9) 1) to 6), 10) 1) to 6), 11)
Current State
Row Active
L L L
Read (AutoPrecharge Disabled) Write (AutoPrecharge Disabled)
L L L L L L L L
1) This table applies when CKEn-1 was HIGH and CKEn is HIGH and after tRC has been met (if the previous state was self refresh). 2) This table is bank-specific, except where noted, i.e., the current state is for a specific bank and the commands shown are those allowed to be issued to that bank when in that state. Exceptions are covered in the notes below. 3) Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. 4) The following states must not be interrupted by a command issued to the same bank. DESELECT or NOP commands, or allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands to the other bank are determined by its current state and according to Table 15. Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank is in the "idle" state. Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank is in the "row active" state. Read with AP Enabled: Starts with registration of a READ command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. Write with AP Enabled: Starts with registration of a WRITE command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state.
Data Sheet
37
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
5) The following states must not be interrupted by any executable command; DESELECT or NOP commands must be applied on each positive clock edge during these states. Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRC is met. Once tRC is met, the SDRAM is in the "all banks idle" state. Accessing Mode Register: Starts with registration of a MODE REGISTER SET command and ends when tMRD has been met. Once tMRD is met, the SDRAM is in the "all banks idle" state. Precharging All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met, all banks are in the idle state. 6) All states and sequences not shown are illegal or reserved. 7) Not bank-specific; requires that all banks are idle and no bursts are in progress. 8) Same as NOP command in that state. 9) READs or WRITEs listed in the Command/Action column include READs or WRITEs with Auto Precharge enabled and READs or WRITEs with Auto Precharge disabled. 10) May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for precharging. 11) Not bank-specific; BURST TERMINATE affects the most recent READ or WRITE burst, regardless of bank.
Table 15 Any Idle
Current State Bank n - Command to Bank m (different bank) CS H L X L L L L L L L L L L L L L L L L L L L L RAS CAS WE Command / Action X H X L H H L L H H L L H H L L H H L L H H L X H X H L L H H L L H H L L H H L L H H L L H X H X H H L L H H L L H H L L H H L L H H L L DESELECT (NOP / continue previous operation) NO OPERATION (NOP / continue previous operation) Any command otherwise allowed to bank n ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) PRECHARGE (deactivate row in bank or banks) ACTIVE (select and activate row) READ (select column and start READ burst) WRITE (select column and start WRITE burst) Notes
1)2)3)4)5)6) 1) to 6) 1) to 6) 1) to 6) 1) to 7) 1) to 7) 1) to 6) 1) to 6) 1) to 7) 1) to 8) 1) to 6) 1) to 6) 1) to 7) 1) to 7) 1) to 6) 1) to 6) 1) to 7), 9) 1) to 9) 1) to 6) 1) to 6) 1) to 7), 9) 1) to 7), 9)
Current State
Row Activating, Active, or Precharging Read (AutoPrecharge Disabled) Write (AutoPrecharge Disabled) Read (with AutoPrecharge) Write (with AutoPrecharge)
1) to 6) PRECHARGE (deactivate row in bank or banks) 1) This table applies when CKEn-1 was HIGH and CKEn is HIGH and after tRC has been met (if the previous state was Self
Refresh). 2) This table describes alternate bank operation, except where noted, i.e., the current state is for bank n and the commands shown are those allowed to be issued to bank m (assuming that bank m is in such a state that the given command is allowable). Exceptions are covered in the notes below.
Data Sheet
38
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Functional Description
3) Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated. Read with AP Enabled: Starts with registration of a READ command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. Write with AP Enabled: Starts with registration of a WRITE command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state. 4) AUTO REFRESH, SELF REFRESH and MODE REGISTER SET commands may only be issued when all banks are idle. 5) A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only. 6) All states and sequences not shown are illegal or reserved. 7) READs or WRITEs listed in the Command/Action column include READs or WRITEs with Auto Precharge enabled and READs or WRITEs with Auto Precharge disabled. 8) Requires appropriate DQM masking. 9) Concurrent Auto Precharge: bank n will start precharging when its burst has been interrupted by a READ or WRITE command to bank m.
Table 16 CKEn-1 L L
Truth Table - CKE CKEn Current State Power Down Self Refresh Clock Suspend Deep Power Down Command X X X X DESELECT or NOP DESELECT or NOP X X DESELECT or NOP DESELECT or NOP AUTO REFRESH (valid) see Table 14 and Table 15 Action Maintain Power Down Maintain Self Refresh Maintain Clock Suspend Maintain Deep Power Down Exit Power Down Exit Self Refresh Exit Clock Suspend Exit Deep Power Down Enter Precharge Power Down Enter Active Power Down Enter Self Refresh Enter Clock Suspend Notes
1)2)3)4) 1) to 4) 1) to 4) 1) to 4)
L
H
Power Down Self Refresh Clock Suspend Deep Power Down
1) to 4) 1) to 5) 1) to 4) 1) to 4), 6) 1) to 4)
H
L
All Banks Idle Bank(s) Active All Banks Idle Read / Write burst
1) to 4) 1) to 4) 1) to 4) 1) to 4)
H
1) 2) 3) 4) 5) 6)
H
CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge. Current state is the state immediately prior to clock edge n. COMMAND n is the command registered at clock edge n; ACTION n is a result of COMMAND n. All states and sequences not shown are illegal or reserved. DESELECT or NOP commands should be issued on any clock edges occurring during tRC period. Exit from DEEP POWER DOWN requires the same command sequence as for power-up initialization.
Data Sheet
39
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Electrical Characteristics
3
3.1
Table 17 Parameter
Electrical Characteristics
Operating Conditions
Absolute Maximum Ratings Symbol min. Values max. 2.7 2.7 V V V V C C C W mA -0.3 -0.3 -0.3 -0.3 0 -25 -55 - - Unit
Power Supply Voltage Power Supply Voltage for Output Buffer Input Voltage Output Voltage Operation Case Temperature Storage Temperature Power Dissipation Short Circuit Output Current Commercial Extended
VDD VDDQ VIN VOUT TC TSTG PD IOUT
VDDQ + 0.3 VDDQ + 0.3
+ 70 +85 +150 0.7 50
Attention: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Table 18 Parameter Input capacitance: CLK Input capacitance: all other input pins Input/Output capacitance: DQ Pin Capacitances1)2) Symbol min. Values max. 3.0 3.0 5.0 pF pF pF 1.5 1.5 3.0 Unit
CI1 CI2 CIO
1) These values are not subject to production test but verified by device characterization. 2) Input capacitance is measured according to JEP147 with VDD, VDDQ applied and all other pins (except the pin under test) floating. DQ's should be in high impedance state. This may be achieved by pulling CKE to low level.
Table 19 Parameter
Electrical Characteristics1) Symbol min. Values max. 1.95 1.95 V V V V V V A A - -
2) 2)
Unit
Notes
Power Supply Voltage Power Supply Voltage for DQ Output Buffer Input high voltage Input low voltage Output high voltage (IOH = -0.1 mA) Output low voltage (IOL = 0.1 mA) Input leakage current Output leakage current
VDD VDDQ VIH VIL VOH VOL IIL IOL
1.70 1.70 0.8 x VDDQ -0.3
VDDQ + 0.3
0.3 - 0.2 1.0 1.5
VDDQ - 0.2
- -1.0 -1.5
- - - -
Data Sheet
40
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Electrical Characteristics
1) 0 C TC 70 C (comm.); -25 C TC 85 C (extended); all voltages referenced to VSS. VSS and VSSQ must be at same potential. 2) VIH may overshoot to VDD + 0.8 V for pulse width < 4 ns; VIL may undershoot to -0.8 V for pulse width < 4 ns. Pulse width measured at 50% with amplitude measured between peak voltage and DC reference level.
3.2
Table 20 Parameter
AC Characteristics
AC Characteristics1)2)3)4) Symbol min. CL = 3 CL = 2 CL = 3 CL = 2 CL = 3 CL = 2 - 7.5 max. -- -- 133 105 5.4 6.0 -- -- -- -- -- -- - 7.0 -- 2 -- -- -- -- 100k -- -- 64 -- ns ns MHz MHz ns ns ns ns ns ns -- --
7) 7) 5)6)
Unit
Notes -- --
Clock cycle time Clock frequency Access time from CLK Clock high-level width Clock low-level width Address, data and command input setup time Address and command input hold time Data (DQ) input hold time MODE REGISTER SET command period DQ low-impedance time from CLK DQ high-impedance time from CLK Data out hold time DQM to DQ High-Z delay (READ Commands) DQM write mask latency ACTIVE to ACTIVE command period ACTIVE to READ or WRITE delay ACTIVE bank A to ACTIVE bank B delay ACTIVE to PRECHARGE command period WRITE recovery time PRECHARGE command period Refresh period (8192 rows)
1) 2) 3) 4) 5)
tCK fCK tAC tCH tCL tIS tIH tMRD tLZ tHZ tOH tDQZ tDQW tRC tRCD tRRD tRAS tWR tRP tREF tSREX
7.5 9.5 -- -- -- -- 2.5 2.5 1.5 0.5 0.8 2 1.0 3.0 2.5 -- 0 67 19 15 45 14 19 --
tCK
ns ns ns
-- -- --
5)6)
tCK tCK
ns ns ns ns ns ns ms
-- --
8) 8) 8) 8) 9) 8)
-- --
Self refresh exit time 1 0 C TC 70 C (comm.); -25 C TC 85 C (extended); VDD = VDDQ = 1.70V to 1.95V;
tCK
All parameters assumes proper device initialization. AC timing tests measured at 0.9 V. The transition time tT is measured between VIH and VIL; all AC characteristics assume tT = 1 ns. Specified tAC and tOH parameters are measured with a 30 pF capacitive load only as shown below:
I/O 30 pF
6) If tT(CLK) > 1 ns, a value of (tT/2 - 0.5) ns has to be added to this parameter. 7) If tT > 1 ns, a value of [0.5 x (tT - 1)] ns has to be added to this parameter.
Data Sheet
41
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Electrical Characteristics
8) These parameter account for the number of clock cycles and depend on the operating frequency, as follows: no. of clock cycles = specified delay / clock period; round up to next integer. 9) The write recovery time of tWR = 14 ns allows the use of one clock cycle for the write recovery time when fCK 72 MHz. With fCK > 72 MHz two clock cycles for tWR are mandatory. Qimonda recommends to use two clock cycles for the write recovery time in all applications.
3.3
Table 21
Operating Currents
Maximum Operating Currents1) Symbol Values - 7.5 60 2.4 Unit Note mA mA
2)3)
Parameter & Test Conditions Operating current: one bank: active / read / precharge, BL = 1, tRC = tRCmin Precharge power-down standby current: all banks idle, CS VIHmin, CKE VILmax, inputs changing once every two clock cycles Precharge power-down standby current with clock stop: all banks idle, CS VIHmin, CKE VILmax, all inputs stable Precharge non power-down standby current: all banks idle, CS VIHmin, CKE VIHmin, inputs changing once every two clock cycles Precharge non power-down standby current with clock stop: all banks idle, CS VIHmin, CKE VIHmin, all inputs stable Active power-down standby current: one bank active, CS VIHmin, CKE VILmax, inputs changing once every two clock cycles Active power-down standby current with clock stop: one bank active, CS VIHmin, CKE VILmax, all inputs stable Active non power-down standby current: one bank active, CS VIHmin, CKE VIHmin, inputs changing once every two clock cycles Active non power-down standby current with clock stop: one bank active, CS VIHmin, CKE VIHmin, all inputs stable Operating burst read current: all banks active; continuous burst read, inputs changing once every two clock cycles Auto-Refresh current: tRC = tRCmin, "burst refresh", inputs changing once every two clock cycles Self Refresh current: self refresh mode, CS VIHmin, CKE VILmax, all inputs stable
IDD1 IDD2P
2)
IDD2PS IDD2N
2.3 13
mA mA
-
2)
IDD2NS IDD3P
2.5 4.2
mA mA
-
2)
IDD3PS IDD3N
4.0 16
mA mA
-
2)
IDD3NS IDD4
3.4 45
mA mA
-
2)3)
IDD5
100
mA
2)
IDD6
2.5 10
mA A
-
4)
Deep Power Down current IDD7 1) 0 C TC 70 C (comm.); -25 C TC 85 C (extended); VDD = VDDQ = 1.70V to 1.95V;
Recommended Operating Conditions unless otherwise noted 2) These values are measured with tCK = 7.5 ns 3) All parameters are measured with no output loads. 4) Value shown as typical.
Data Sheet
42
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Package Outlines
4
Figure 47
Package Outlines
PG-VFBGA-54-8 (Plastic Green Very Thin Fine Pitch Ball Grid Array Package)
You can find all of our packages, sorts of packing and others in our Qimonda Internet Page : http://www.qimonda.com/products. SMD = Surface Mounted Device Data Sheet 43 Dimensions in mm Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
List of Figures
Figure 1 Standard Ballout 256-Mbit Mobile-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 2 Functional Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 3 Power-Up Sequence and Mode Register Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 4 State Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 5 Address / Command Inputs Timing Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 No Operation Command 14 Mode Register Set Command 15 Figure 8 Mode Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ACTIVE Command 16 Figure 10 Bank Activate Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 READ Command 17 Figure 12 Basic READ Timing Parameters for DQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 13 Single READ Burst (CAS Latency = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 14 Single READ Burst (CAS Latency = 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 15 Consecutive READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 16 Random READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 17 Non-Consecutive READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 18 Terminating a READ Burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 19 Clock Suspend Mode for READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 20 READ Burst - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 21 READ to WRITE Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 22 READ to PRECHARGE Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 WRITE Command 24 Figure 24 Basic WRITE Timing Parameters for DQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 25 WRITE Burst (CAS Latency = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 26 WRITE Burst (CAS Latency = 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 27 Consecutive WRITE Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 28 Random WRITE Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 29 Non-Consecutive WRITE Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 30 Terminating a WRITE Burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 31 Clock Suspend Mode for WRITE Bursts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 32 WRITE Burst - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Figure 33 WRITE to READ Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Figure 34 WRITE to PRECHARGE Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 BURST TERMINATE Command 30 PRECHARGE Command 31 Figure 37 READ with Auto Precharge Interrupted by READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Figure 38 READ with Auto Precharge Interrupted by WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Figure 39 WRITE with Auto Precharge Interrupted by READ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Figure 40 WRITE with Auto Precharge Interrupted by WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 AUTO REFRESH Command 34 Figure 42 Auto Refresh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SELF REFRESH Entry Command 35 Figure 44 Self Refresh Entry and Exit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Power Down Entry Command 36 Figure 46 Power Down Entry and Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Data Sheet
44
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
List of Tables
Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Memory Addressing Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Burst Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Command Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Inputs Timing Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Timing Parameters for Mode Register Set Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Timing Parameters for ACTIVE Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Timing Parameters for READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Timing Parameters for WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Timing Parameters for PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Timing Parameters for AUTO REFRESH and SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Current State Bank n - Command to Bank n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Current State Bank n - Command to Bank m (different bank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Truth Table - CKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Pin Capacitances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Maximum Operating Currents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Data Sheet
45
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
HY[B/E]18L256169BFX-7.5 256-Mbit Mobile-RAM
Table of Contents
1 1.1 1.2 1.3 1.4 2 2.1 2.2 2.2.1 2.2.1.1 2.2.1.2 2.2.1.3 2.2.1.4 2.2.1.5 2.2.1.6 2.2.1.7 2.2.1.8 2.3 2.4 2.4.1 2.4.2 2.4.3 2.4.4 2.4.5 2.4.5.1 2.4.5.2 2.4.5.3 2.4.5.4 2.4.5.5 2.4.6 2.4.6.1 2.4.6.2 2.4.6.3 2.4.6.4 2.4.6.5 2.4.7 2.4.8 2.4.8.1 2.4.8.2 2.4.9 2.4.9.1 2.4.9.2 2.4.10 2.4.10.1 2.5 3 3.1 3.2 3.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Definition and Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 4 4 5
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Power On and Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Burst Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Burst Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Read Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Write Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Extended Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Partial Array Self Refresh (PASR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Temperature Compensated Self Refresh (TCSR) with On-Chip Temperature Sensor . . . . . . . . 11 Selectable Drive Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 NO OPERATION (NOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DESELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 MODE REGISTER SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ACTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 READ Burst Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Clock Suspend Mode for READ Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 READ - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 READ to WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 READ to PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 WRITE Burst Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Clock Suspend Mode for WRITE Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 WRITE - DQM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 WRITE to READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 WRITE to PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 BURST TERMINATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 AUTO PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 CONCURRENT AUTO PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 AUTO REFRESH and SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 AUTO REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 POWER DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 DEEP POWER DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Function Truth Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 40 41 42
Data Sheet
46
Rev. 1.01, 2007-01 07062006-V6ZK-PGR3
Data Sheet
Edition 2007-01 Published by Qimonda AG Gustav-Heinemann-Ring 212 D-81739 Munchen, Germany (c) Qimonda AG 2007. All Rights Reserved. Legal Disclaimer The information given in this Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office. Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Qimonda Office. Under no circumstances may the Qimonda product as referred to in this Data Sheet be used in 1. Any applications that are intended for military usage (including but not limited to weaponry), or 2. Any applications, devices or systems which are safety critical or serve the purpose of supporting, maintaining, sustaining or protecting human life (such applications, devices and systems collectively referred to as "Critical Systems"), if a) A failure of the Qimonda product can reasonable be expected to - directly or indirectly (i) Have a detrimental effect on such Critical Systems in terms of reliability, effectiveness or safety; or (ii) Cause the failure of such Critical Systems; or b) A failure or malfunction of such Critical Systems can reasonably be expected to - directly or indirectly (i) Endanger the health or the life of the user of such Critical Systems or any other person; or (ii) Otherwise cause material damages (including but not limited to death, bodily injury or significant damages to property, whether tangible or intangible). www.qimonda.com

▲Up To Search▲

Price & Availability of HYE18L256169BFX-75

	To Download HYE18L256169BFX-75 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .